

Ultracompact, all-in-one softening and filtration system
Installation video: https://youtu.be/cqMOGoaTTbc
S550 P1 – model with the special media for hydrogen sulfide removal. The filter media in this model contains KDF 85 for H2S content reduction. The expanded functions of the system include water softening, removal of hydrogen sulfide, iron and manganese.
S550 – model without hydrogen sulfide removal
Exceptionally salt- and water-efficient whole-home water softener. It is also an eco-friendly solution: damaging salt emissions are reduced by up to 30%.
Requires up to 30% less salt
Maximum efficiency with minimum salt consumption thanks to the unique tank design and extra-fine ion exchange resin. The latter lasts 10 times longer than that in typical water softeners.
2-in-1: water softening & iron removal
Removal of high concentration of Fe (up to 14 mg/L) and hardness salts.
Patented technologies for the longer life
AQUAPHOR softeners contain patented high-efficiency Dual Core Valves and other engineering solutions to ensure long-term trouble-free performance.
Removes from water:
• Dissolved iron (up to 10 mg/l)
• Hardness salts (up to 24 meq/l)
• Manganese (up to 3 mg/l)
Solves all problems!
Automatic controller – controls the operation of the valve during water filtration and regeneration. Built-in battery: a power outage does not cause the current settings to fail.
Patented control valve – ensures trouble-free operation of the filter throughout its entire service life.
Self-washing sand pre-filter – protects the ion-exchange resin from mechanical impurities.
Ion Exchange Resin – The S550 uses a very fine calibrated ion exchange resin. It has a large specific surface area. This increases the efficiency of the filter both during operation and during regeneration.
Mesh flow distributor – the sorbent is sandwiched between two meshes with cells of 100 microns. This allows the use of a superfine ion exchange resin, which improves filter efficiency over conventional softeners by up to 300%.
Durability matters!
The Aquaphor S550 filter housing is made of thick-walled structural reinforced polymer. As a result, it is extremely resistant to internal and external loads.
Characteristics
Maximum compensated hardness, mg/l – 1200
Productivity working/maximum, l/min – 23/25
The maximum concentration of dissolved iron, mg / l – 10
Minimum pH – 6
Maximum flow to the drain during regeneration, l/min – 7.6
Dimensions (H × W × D) – 55.4 × 35.5 × 46.5 cm
Weight – 35 kg
Productivity – 1,4 m3/hour
Source water requirements*
Water hardness, meq / l – no more than 24
The content of ferrous iron, mg / l – no more than 10
The content of ferric iron, mg / l – no more than 0.3
Manganese content, mg/l – no more than 3
pH – from 6 to 9
Temperature, ° С – from +5 to +38
Hydrogen sulfide, mg/l – no more than 0.03
Permanganate oxidizability, mgО2/l – no more than 5
Silicon, mg/l – no more than 10
*For details, please refer to the product instruction manual.
The problem of water purification arises in front of almost every owner of a country house. Water from a well, a well or a village water supply can not only ruin plumbing, but also be harmful to health.
Hard water
• Increases the consumption of detergents (washing powder, shampoo, soap) by 3–4 times.
• Increases energy consumption for water heating by 30–50%.
• Reduces the service life of household appliances by 3-5 times due to the formation of scale on heating elements.
• Disables plumbing.
• Causes dryness and premature aging of the skin.
• Provokes exacerbation of atopic dermatitis.
Model | S550 | S550 P1 |
Manufacturer | Aquaphor | Aquaphor |
Removes hydrogen sulfide | no | yes |
Maximum Compensated Hardness, gpg | 24 | 24 |
Maximum Ferrous Iron Reduction, ppm* | 10 | 10 |
Minimum pH, standard units | 6 | 6 |
Maximum Flow Rate to Drain During Regeneration, gpm (L/min) | 2,0 (7,6) | 2,0 (7,6) |
Productivity | 1,4 m3/hour | 1,4 m3/hour |
Productivity working/maximum, l/min | 23-25 | 23-25 |
Dimensions (H×W×D), mm | 554 × 355 × 465 | 554 × 355 × 465 |
Weight, kg | 35 | 35 |